📖 Free WLED Guide — Norwegian Step-by-Step

📖 Free WLED Guide — Norwegian Step-by-Step

0,00 kr
Skip to product information
📖 Free WLED Guide — Norwegian Step-by-Step
  • 📖 Free WLED Guide — Norwegian Step-by-Step
  • 📖 Free WLED Guide — Norwegian Step-by-Step
📖 Free WLED Guide — Norwegian Step-by-Step

📖 Free WLED Guide — Norwegian Step-by-Step

0,00 kr
Norwegian Step-by-Step Guide: Flashing, Connecting, and Setting up Home Assistant with WLEDThis guide is designed for your "Complete WLED Aurora Package" from AuroraLys.no. It will take you through the entire process step by step – from flashing WLED firmware onto the ESP32 controller, to physically connecting the components, and finally setting it up in Home Assistant on Raspberry Pi 5. The guide is for beginners, but includes tips for advanced users.You can download this as a PDF from the store (or copy the text into a tool like Google Docs/Canva and export as PDF). Estimated time: 1-2 hours. Tools you need: PC with USB-C cable, WiFi network, and basic soldering tools if you wish to customize.1. Preparations
  • Package contents to check: Raspberry Pi 5 kit (board, case, fan, PSU, SD card), ESP32 WLED controller (orange model GL-C-017WL), 2 x 5m WS2815 LED strip (white/black PCB, IP20/65/67), 12V power supply (100-240W).
  • Software: Download WLED-installer from wled.me (web-based, no installation). Install Home Assistant OS on the SD card if not pre-flashed (use Raspberry Pi Imager from raspberrypi.com).
  • Safety tips: Work on an ESD-safe mat (anti-static). Use a 12V PSU with at least 200W for a 10m strip – avoid overloading. Always test with low brightness first.
2. Flashing WLED on the ESP32 ControllerWLED is firmware that turns ESP32 into a smart LED controller. This takes 5-10 minutes.
  • Step 1: Connect the ESP32 to your PC with a USB-C cable. The controller should appear as a device (like a USB stick).
  • Step 2: Open a web browser (Chrome recommended) and go to install.wled.me.
  • Step 3: Select "Install to ESP32" (or specific variant if asked). Follow the instructions: Choose COM port (see Device Manager on Windows or lsusb on Mac/Linux).
  • Step 4: Wait for flashing (approx. 1-2 min). The ESP32 will restart and create a WiFi hotspot called "WLED-AP".
  • Step 5: Connect to the hotspot (password: wled1234). Open 4.3.2.1 in your browser to configure: Select your home WiFi, set password, and save. The ESP32 will connect to your network – note the IP address (e.g., 192.168.1.xx).
  • Tips: If flashing fails, try a different USB cable or restart your PC. Advanced: Activate mic/IR sensor in WLED settings for sound/gesture effects.
3. Connecting the HardwareNow we will connect the LED strips, the controller, and the power supply. Use jumper wires or soldering for secure connections.
  • Step 1: Prepare the LED strips: Connect the two 5m WS2815 strips in series (Data out from the first to Data in on the second). WS2815 has 4 pins: 12V (red), GND (black), Data (green), Backup Data (white – connect if desired for redundancy).
  • Step 2: Connect to ESP32 controller:
    • Power: 12V from PSU to ESP32's VIN/GND (use level shifter if included for safety).
    • Data: ESP32 GPIO (e.g., pin 16) to the strip's Data in (green). Connect GND in common.
    • For longer strips: Inject power every 5m (connect extra 12V/GND from PSU to the end of the strip to avoid voltage drop).
  • Step 3: Connect PSU: Plug 12V PSU into wall outlet – start with low brightness in WLED (see next step).
  • Step 4: Test: Go to ESP32's IP in your browser (from step 2). In the WLED app: Set LED count (600 for 10m/60 LEDs/m), type (WS2815), and test effects. Adjust brightness to 50% first.
  • Tips: For waterproof (IP65/67): Use silicone/heat shrink on connections. Black PCB for a discreet look, white for better light diffusion. If flickering: Check GND connections or use a higher W PSU.
4. Setting up Home Assistant on Raspberry Pi 5Home Assistant (HA) controls everything via app/web – including WLED for automations.
  • Step 1: Insert the SD card into the Pi 5 (pre-flashed with HA OS if included; otherwise use Raspberry Pi Imager to download HA OS from home-assistant.io).
  • Step 2: Connect Pi to screen (HDMI), keyboard/mouse, and Ethernet/WiFi. Start Pi – wait 5-10 min for first boot (HA installs itself).
  • Step 3: Open homeassistant.local:8123 in a browser on the same network. Create an account, select timezone (Norway/Oslo), and configure WiFi if necessary.
  • Step 4: Integrate WLED: In HA > Settings > Devices & Services > Add integration > Search "WLED". It will automatically detect ESP32 (via mDNS). Select the device, set a name (e.g., "Aurora Living Room"), and save.
  • Step 5: Test in HA: Go to Overview > Add card > Select WLED device. Try effects, automations (e.g., "Activate aurora at sunset").
  • Tips: Install the HA app on your mobile for remote control. For advanced users: Add YAML automations for gesture-triggered or mic-based light shows. Update HA regularly via Settings > System.
5. Troubleshooting and Advanced Tips
  • Common problems: No lights? Check data polarity or flashing. HA can't find WLED? Check the same network/IP. Overheating? Use Pi fan and lower brightness.
  • Advanced: Sync multiple controllers in WLED. Use HA add-ons like ESPHome for custom firmware. For aurora effects: Download WLED presets from the community (search "aurora WLED preset").
  • Support: Visit forums like home-assistant.io or wled.discourse.group. Contact us at AuroraLys.no for help!
This guide is based on a standard setup – customize it to suit your arrangement. Good luck with your aurora project! 🌌 (To create PDF: Copy the text into Word/Google Docs, add images from previous suggestions, and export as PDF. Add logo and footer with "AuroraLys.no – December 2025".)

You may also like